An overview of the RTLS location technologies from AiRISTA

 

AiRISTA has an active R&D lab where a range of technologies are put to the test. Some of these technologies are productized and described below. Others, like LoRa and UWB, are evaluated and a design is created in case the market dictates a shift in that direction. This is one in a series of blogs that will eventually explore the pros & cons of each technology and examples use cases. 

 

Passive RFIDPassive RFID Chip

Passive RFID systems consist of tags and readers. The reader is a networking device similar to a access point that emits a directed radio signal in the UHF frequency. The tag is a simple device consisting of a chip and an antenna. The antenna absorbs the UHF energy from the reader and reflects that energy back to the reader with the chip’s unique identifier.

 

BLE Proximity

A1 Wrist StrapLike passive RFID, BLE proximity uses a reader device to detect a signal emitted by a BLE tag. The tag, in this case, is battery powered which provides greater range than a passive tag. The strength of the tag’s BLE signal is inversely proportional to the distance. Changing the characteristics of the reader’s antenna, the field of detection can be tuned for wider or narrower fields of capture. Pictured to the left is the AiRISTA A1 BLE tag. 

 

Received Signal Strength Indicator (RSSI)RSSI Triangulation

Active RFID tags (aka RTLS tags) use a battery to produce a wireless signal. Wi-Fi and Bluetooth® Low Energy (BLE) are typical radios and these signals are detected by receivers (typically your existing access points). The receiver records the strength of the received signal and compares that value with other access points receiving the same signal. Knowing the location of each access points and the received signal strength, the tag’s location can be determined using trilateration – the stronger the signal, the closer is the tag to the access point.

 

BLE Angle of Arrival & Angle of Departure (AoA & AoD)

AoA-1Rather than using relative signal strength, AoA uses a receiver (reader) that uses the “angle” of the BLE signal as it arrives from the tag. The angle is compared among a series of micro-antenna precisely located on the antenna substrate. The minute differences between the micro-antenna trace back vectors that converge on the location. Note, “angle” is an easy way to conceptualize the process, but it’s actually the difference in the phase of the arriving signal).

AoD uses the same principles but reverses the model where the item being tracked is calculating location based on the angle of the departing signal from 2 or more fixed beacons.

 

BLE High Accuracy Distance Measurement (HADM)

HADM uses very simple infrastructure to achieve accuracy of 10’s of centimeters. As a signal travels from transmitter to receiver and back, the signal’s phase shifts proportionate to the distance. The magnitude of the phase shift is used to calculate the distance. To remove the effect of multipath (reflected signals that act like echoes), frequency hopping is used to compare phase shift at multiple frequencies. AiRISTA expects fully productized solutions in early 2023.

Phase based Ranging-1

 

Global Positioning System (GPS)W9

Global positioning systems use a series of 30+ low-orbit satellites which transmit their precise location to receivers on earth. When a tag with a GPS receiver detects 4 or more satellites, the receiver uses trilateration to calculate its longitude and latitude based on its distance from each satellite. As with RSSI, accuracy increases with the more satellites the tag recognizes. A65-1Although the tag only receives GPS signals (the tag does not transmit), it is nonetheless power hungry. If they don’t have a constant power source, tags using batteries can conserve power by shutting down when GPS tracking is not needed.

Pictured above, right is the AiRISTA W9 personnel tag with GPS as well as cellular technology. Pictured to the left is the AiRISTA A65 tag asset tag for indoor and outdoor tracking using GPS.

 

Batteryless BLE

Similar to passive RFID, batteryless BLE uses ambient radio energy to power the tag. Places like work, home or the shopping mall are under constant bombardment by radio devices providing a rish source of power. The batteryless tag contains a chip and antennae which reflect this harvested energy in the form of a unique identifier in the BLE spectrum. Unlike traditional RTLS systems which require specific devices like access points to receive the tag’s signal, common devices like your personal cell phone or an Echo Dot can detect the tag and pass along its ID over legacy networks like your phone’s cellular service or your surrounding Wi-Fi.

AiRISTA is evaluating the technology in its R&D labs and is excited about its potential, but has no product based on batteryless BLE at this time.

 

To find out more about AiRISTA RTLS technologies download the FREE white paper that explores the pros & cons as well as example use cases.